DSI Top

Search:

Type: Posts; User: Gone Green

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    2,887

    Re: Dime Tahiti hull

    That's Way Cool..you might find him on Performance Boats
  2. Replies
    73
    Views
    18,385

    Re: Five hundred forty five cubic inches Baby

    Hey Rich, does Nathan have a dyno hidden in his shop?
  3. Replies
    76
    Views
    20,259

    Re: 527 cubic inches

    Steve, you kinda lost me on this one, D ports flush top edge of ? Raise top 4"..allways thought the plenum on these were not enough ....This sounds like OLD Ram Charger stuff
  4. Replies
    3
    Views
    3,279

    Re: Jetaway not engaging

    I bought mine new, they don't come with a diagram, you will have to send it to Hi-Tec....the unit should Always be engaged except trailer running, leaving it in neutral for a long time Does weaken...
  5. Thread: Loaders

    by Gone Green
    Replies
    9
    Views
    3,969

    Re: Loaders

    Not sure what that means
  6. Thread: Loaders

    by Gone Green
    Replies
    9
    Views
    3,969

    Re: Loaders

    ,
    If it's factory installed you will need a hand held Impact driver and 3# sledge to bust the bolts, then drill thru and use stainless bolts, washers and nylocks...grade #8 is what I recommend for...
  7. Replies
    14
    Views
    3,859

    Re: Hyper pistons

    Unless your running a blower those pistons are fine for you, my kid pulls 5900 with a B cut bronze imp.
    If you decide to change the pistons just balance the pistons
    Overrev? MSD Box
  8. Replies
    14
    Views
    3,859

    Re: Hyper pistons

    My son has been running the KB hyper pistons about 10 yrs. no issues...and yes, he runs it hard
  9. Replies
    6
    Views
    1,652

    Re: Quick fuel tech

    They use China main bodies,yea assembled in Kentucky....bought them, cant tune them=junk
    Braswell the Best...big doller
    Dan Davinci,or John Avery....Great Quality Fair Price, built for your engine
  10. Replies
    14
    Views
    4,062

    Re: Intake manifold recommendation for 454 BBC

    We had great success with Edelbrock Air-Gap, 750 holly and 2" Wilson manifold spacer..on Oval-Ports
  11. Replies
    10
    Views
    2,213

    Re: Newb with a 1978 Sunkisst needing help

    A CP Tunnel ???? you will get spit out, not if, but when....
  12. Replies
    10
    Views
    2,213

    Re: Newb with a 1978 Sunkisst needing help

    You'll have a lot of fast fun with that..18' straight side, a tunnel will hurt you on the lake
  13. Replies
    10
    Views
    2,213

    Re: Newb with a 1978 Sunkisst needing help

    Do you have a picture of the boat?
  14. Replies
    76
    Views
    20,259

    Re: 527 cubic inches

    Looks good Steve..how much lash for the cam?..also what quench do the fords like?
    Chevys are gold with .40
  15. Replies
    14
    Views
    6,498

    Re: Camp Far West Fathers Day 2016

    Nice Steve...went out sat. to look around, the blue and white cp was parked next to a cp tunnel, did they run? Do you have info on those two?
  16. Replies
    32
    Views
    11,580

    Re: 75 Eliminator

    You are Very lucky
  17. Replies
    32
    Views
    11,580

    Re: 75 Eliminator

    Assuming you have the correct head gasket...did you put the alignment dowels in?
    are you using a by-pass valve from pump to engine
  18. Replies
    120
    Views
    24,142

    Re: My 78 Sonic 496 stroker build project!

    I would build a Good platform for the torque your going to throw at it..........a 496 is Way more torque than a small block, Rail-kit, Pump brace-Good Pump
  19. Replies
    7
    Views
    2,748

    Re: CFW accident yesterday

    You Know it was a Bladder Boat..Fucking Dangerous to come across, in a river they do about 40, and kick a 7ft. wake
  20. Replies
    18
    Views
    2,939

    Re: New member looking for advice on his Kona

    I got mine from CP Performance, as a package deal..I see now you can get a package that includes a inducer impeller also.
    Not saying your going to twist your stock shaft, But if you continue to up...
  21. Replies
    18
    Views
    2,939

    Re: New member looking for advice on his Kona

    Stainless or Bronze impeller, aqua-shaft, and rail kit
  22. Replies
    21
    Views
    8,507

    Re: CFW Hot Boat Bash 2016

    Is south shore open?
  23. Replies
    76
    Views
    20,259

    Re: 527 cubic inches

    Rex and Glen doing your stuff?
  24. Replies
    20
    Views
    3,844

    Re: Fuel Pump Question/ Spark Plug Question

    The Holley Blue, I ran for many years 468 chevy, 2 660's ..good pump, just install at a low point in the boat, these are push-pumps, not pull pumps!
    Check float level..and timming
  25. Replies
    76
    Views
    20,259

    Re: 527 cubic inches

    Hondo or Tahiti?
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4