DSI Top

Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles
  • genrystuart79's Avatar
    04-24-2019, 02:13 AM
    Ok, thx, found someone, will come today.
    8 replies | 3216 view(s)
  • Matt_pocket's Avatar
    04-23-2019, 02:57 AM
    Try UCM Services.
    8 replies | 3216 view(s)
  • T8er S.'s Avatar
    04-20-2019, 05:50 AM
    Yet another reason your boat should be loud and fast.... https://www.youtube.com/watch?v=TTW7Ti_Pp-M&feature=share&fbclid=IwAR02QE_wu9R6JjAHckF2FjOBVbekqd0KgWAIQanop4Vst4RQyTNdxftZFdo :fighting72:
    3 replies | 2463 view(s)
  • "THE ADVOCATE"'s Avatar
    04-19-2019, 05:08 PM
    And this is why I get up at 3:00am from Sept 29th till the close of migratory hunting. Hopefully I have saved a life
    534 replies | 92989 view(s)
  • Sleek Freak's Avatar
    04-18-2019, 10:55 AM
    nice score on your Aristocrat. cool project with great looking body lines and the fact that you have the engine cover takes her over the top.. if you do Facebook you can go to the Sleek Craft boat owners site for info.
    10 replies | 476 view(s)
  • T8er S.'s Avatar
    04-17-2019, 05:57 PM
    Proof positive that you lost... :CRAPFAN:
    534 replies | 92989 view(s)
  • T8er S.'s Avatar
    04-17-2019, 05:54 PM
    T8er S. replied to a thread Twisted words in Wide Open
    :boxing:
    1736 replies | 261976 view(s)
  • wardjr's Avatar
    04-17-2019, 04:24 PM
    I donít know Panthers but Berks are glued in pretty damn well. It took a lot of cutting (Fein or dremel multi tool helps) and prying. Then some more cutting and prying. Eventually something started to give and things got a lot easier. Once you reinstall yours youíll see why they are so hard to get out. Lots of 5200 to seal the housing to the hull and it is some tough stuff. Keep up the good work!
    10 replies | 476 view(s)
  • T8er S.'s Avatar
    04-17-2019, 03:28 PM
    https://www.youtube.com/watch?v=bCFkSAqqMLs :36_1_55:
    10 replies | 476 view(s)
  • azjimbob's Avatar
    04-17-2019, 12:36 PM
    Working continues: Removed all the guages, and steering wheel. Not sure if any of the guages work so I'm planning on replacing them all. Will also replace the fuel senders in both saddle gas tanks. (nned to get them cleaned up and pressured tested to make sure they are ok to use Still can't get the Panther off the boat. I separated the drive (found a nice dead spider) Any suggestions would be appreciated!! Have sanded the entire top of the boat, and now am filling a few chips lefts and the holes left from the rivets that held the rub rail on. Net week well try my hand at some fiberglass on the area where the ski pylon was and will add some fiberglass and wood to the engine cover to reinforce it. Just to let you all know that this is the first boat I've owned, but am loving it and looking forward to seeing it on the water.
    10 replies | 476 view(s)
No More Results